The neutral safety switch stops working when the vehicle will not start in neutral. The security switch is not working if the auto starts in gear.

You are watching: Replace neutral safety switch chevy truck


\"*\"

Step 3: progressive the vehicle. Background under the automobile at its specified jacking points until the wheel are completely off the ground.

\"*\"

Step 4: location the jack stands. The jack stands have to go under the jacking point locations and lower the automobile onto the jack stands.

For most modern cars, the jacking points for jack stands will be on the pinch weld just under the doors follow me the bottom the the car.

Note: best to monitor the vehicles owners manual for suitable jacking locations.

Part 3 that 8: remove the obelisk shifter neutral safety and security switch

Materials Needed

Boxed end wrenchesFastener remover (only for vehicles v engine guard)Nine volt battery saverRatchet through metric and also standard socketsSmall punchSmall pry barTorques little bit set

Step 1: download a nine volt battery saver right into your cigarette lighter. This will certainly keepyour computer system live and also keep your setting current in the vehicle.

If you perform not have actually a nine volt battery saver, that is no a big ordeal.

\"*\"

Step 2: open up the hood and also disconnect the battery. Remove the negative post off of the battery terminal.

This discharges the strength to the neutral safety and security switch.

Step 3: get your creeper and also tools. Walk under the vehicle and also locate the neutral safety and security switch.

Step 4: remove the shifter linkage attached to the shifter top top the transmission. This linkage may be installed with a bolt and also lock seed or through a boss pin and also cotter pin.

Step 5: remove the mounting bolts to the neutral security switch.

Step 6: Unplug the harness to the neutral security switch. You might need to usage a tiny pry bar to popular music the exploit off.

Step 7: remove the nut from the shifter shaft on the transmission. Take turn off the shifter affiliation bracket.

Note: most shifter shafts ~ above a transmission will lock right into park with turning clockwise.

\"*\"

Step 8: eliminate the switch. Utilizing the little pry bar, apply slight pressure versus the neutral safety and security switch and the transmission and remove the switch.

Note: The old switch might break when removing due to rust or contamination.

Part 4 that 8: removed the digital floor shifter neutral safety and security switch

Materials Needed

Boxed finish wrenchesFastener remover (only because that vehicles with engine guard)Nine volt battery saverRatchet through metric and standard socketsSmall punchSmall pry barTorques little bit set

Step 1: download a ripe volt battery saver into your cigarette lighter. This will keepyour computer live and keep your setting current in the vehicle.

If you carry out not have a ripe volt battery saver, climate it is okay.

Step 2: open the hood and also disconnect the battery. Eliminate the an adverse post turn off of the battery terminal.

This discharges the strength to the neutral safety switch.

Step 3: carry your tools v you in the passenger next of the vehicle. Eliminate the carpet roughly the shifter housing.

Step 4: remove the mounting bolts ~ above the floor board. These are the bolts the secure the floor shifter.

Step 5: pick up the floor shifter assembly and detach the harness. Rotate the shifter assembly over and also you will see the neutral security switch.

Step 6: eliminate the neutral safety switch from the shifter housing. Be sure to clean the call on the exploit of the automobile prior to installation.

Part 5 that 8: installing the pillar shifter neutral safety switch

Materials Needed

Boxed finish wrenchesFastener remover (only for vehicles with engine guard)Nine volt battery saverRatchet with metric and also standard socketsSmall punchSmall pry barTorques little bit set

Step 1: check that infection is in park. Making use of the shifter affiliation bracket, turn the shifter column on the transmission clockwise, ensuring that the transmission is in park.

Step 2: download the new neutral security switch. Usage Anti-Seize ~ above the shifter obelisk to avoid rust and also corrosion in between the shaft and also the switch.

Step 3: Screw in the mounting bolts by hand. Torque the bolts to appropriate specs.

If you perform not know the specification because that the bolt torque, you can tighten the bolts 1/8 turn.

Warning: Tightening the bolts also tight will certainly crack the new switch

\"*\"

Step 4: plugin the exploit to the neutral safety and security switch. Make certain that the lock engages and also secures the plug.

Step 5: install the shifter affiliation bracket. Tighten the seed to the ideal torque specifications.

If you perform not recognize the specification for the bolt torque, you have the right to tighten the bolts 1/8 turn.

Step 6: download the link onto the linkage bracket. Tighten the bolt and nut up tight.

Use a new cotter pen if the link was attached by a ceo pin.

Warning: carry out not usage the old cotter pin due to work harden and fatigue. The oldcotter pin might break prematurely.

Step 7: Hook increase the an unfavorable battery cable to the an adverse terminal. This will supply strength to the new neutral security switch.

Remove the nine volt battery saver from the cigarette lighter.

Part 6 of 8: installing the electronic floor shifter neutral safety and security switch

Materials Needed

Allen wrench setBoxed finish wrenchesFastener remover (only for vehicles with engine guard)Nine volt battery saverRatchet through metric and also standard socketsSmall punchSmall pry barTorques bit set

Step 1: download the brand-new neutral safety switch right into the shifter housing.

Step 2: location the floor shifter top top the floor board. Affix the exploit to the floor shifter and place the floor shifter down onto the floor board.

\"*\"

Step 3: download the mounting bolts ~ above the floor board. This secure the floor shifter.

Step 4: install the carpet around the shifter housing.

Step 5: Hook up the an adverse battery cable come the negative terminal. This will certainly supply strength to the brand-new neutral security switch.

Remove the nine volt battery saver from the tobacco lighter.

Part 7 the 8: Lowering the vehicle

Step 1: raise the vehicle. Background under the auto at its mentioned jacking points until the wheel are fully off the ground.

Step 2: eliminate the jack stands. Save them much away native the vehicle.

Step 3: lower the auto to where all four wheels space on the ground. Pull out thejack and put it aside.

Step 4: remove the wheel chocks indigenous the behind wheels. Put these aside.

Part 8 the 8: experimentation the brand-new neutral safety switch

\"*\"

Step 1: Make sure that the shifter is in the park position. Rotate on the ignition crucial andstart the engine.

Step 2: turn the ignition turn off making the engine shut off. Location the shifter right into neutral position.

Turn ~ above the ignition vital and start the engine. If the neutral security switch is working appropriately the engine will start.

To check the neutral safety switch, shut the engine off and also restart the engine 3 times in the park position and three time in the neutral place on the shifter. If the engine starts up every time, climate the neutral security switch is functioning correctly.

See more: Which Statement Best Describes How Work And Power Are Different? ?

If friend cannot acquire the engine to begin up in the park or neutral position or if the engine starts increase in equipment after replacing the neutral security switch, climate you need more diagnosis the the neutral safety switch and also you may have electric failure. If the trouble persists, climate you need to seek out help from among rebab.net’s certified mechanics the can inspect the clutch and transmission and also diagnosis the problem.