You have to learn how to readjust steering top top zero revolve mower ifyou’re encountering the complying with hiccups.

You are watching: How to adjust steering on toro zero turn mower

It won’t remain straight and tends to pull left (or right) when driving forward.It frequently jerks/spins once turning.The zero rotate no much longer reverses evenly.

In general, many of the adjustments covered in this article apply to all the typical models: Husqvarna, MTD, Cub Cadet, troy bilt, and Toro zero-turn mowers.

I don’t desire to store you wait so stop dive best in.

How to adjust steering ~ above zero revolve mower: step by step overview

For all brands, operation the basics before proceeding toimplement the major adjustments.

Basic procedures

Here is what friend should inspect right off the bat:

1.Measure the tire pressure

Tire press affects mower tracking so it’s an essential for the machine to have actually the recommended tires pressure.


IRWIN VISE-GRIP adjustable Wrench Set, SAE, 8-Inch...

Cub cadetzero turnsnow blowerattachment

Increase/decrease journey wheel speed

You see, the factor why the mower could be veering towardsone direction is the the journey wheel top top one next is transforming slower than its ‘partner’.

Hence, to exactly the issue, it’s one of two people you slow-moving down the fasterwheel or speed up the sluggish wheel.

So, exactly how do we execute this?

Again the nothing complex in many models.

Here are the steps:

1. Determine the means your mower turns (left/right).

2. Loosen the nut (it have the right to either be a jam or traditional nut)on the unit’s mediate bolt.

3. Adjust the speed by either:

Turning the mediate bolt clockwise- this willdecrease the steering lever travel.Turning the adjustment bolt counterclockwise-this will rise the steering bar travel.

4. Retighten the nut.

If you control the steering lever travel together described, yourunit must stop transforming to the right/left as soon as you push both steering leversforward.

Align steering levers

It’s also a good idea to job-related on the steering levers as youtry to rein in top top the aer steering.

For the many part, adjusting the steering calls for that youloosen the 2 arms climate align castle to suitable position.

The adjustment need to be make in the order described below ifit’s your an initial time to do this.


1. Adjust the Steering lever HeightRemove the hardware securing the handlebar tothe upper control arm.Move the handlebar up/down come align the mountingholes through the desired adjusting holes.Reinstall and also retighten the hardware.2.Adjust the steering bar widthTurn your fist to the lower control arm andstart by loosening the hardware located at its base.Locate the eccentric spacer and also loosen the nuton the hex bolt supporting the eccentric spacer. Readjust the spacer (just rotate) accordingly forboth arms.Tighten the hardware.

3.Follow these actions to readjust the steering leverreach (Forward or Backward).

Loosen the hardware securing the steeringcontrol come the upper regulate arm.Rotate the steering bar eitherforward/backward to her comfort.Tighten the bolts starting with the upper bolt.

Watch this video for comprehensive instructions on adjusting the steering levers if you own an Arien IKON X zero turn.

How to readjust steering top top zero rotate mower: added ideas

I would also like to suggest out a few other hacks that canmake friend achieve precise steering.

Some the these possible solutions may, however, require you come consult a fix center, specifically if you’re not a DIY guru.

Let us begin.

·Replace the unit’s former axle pivot

In part cases, the trouble won’t go away also after tryingall the above suggestions and you need to think external the box.

Your first destination need to be the zero rotate mower frontaxle…

Of course, you must be certain that it requirements replacement beforeperforming this activity and the clearest sign is the front wheels pointingoutward-you don’t expect specific steering under together conditions.

There’s a cost however it can ultimately bring the relief youhave been looking for.

·Check the tie rod

Another point you might require to readjust is the stick runningin between the left-hand lever and the left rear wheel hydrostatic drive.

This helps push the short lever further forward come createmore balance.

If the steering is quiet wobbly, then think about replacing therod.

·Change the zero turn’s wheel spindle assembly

Your steering might be suffering due to a destroyed or bend wheelspindle.

The foolproof equipment is again a replacement but you wantto develop the state that the assembly prior to undertaking the change.

A straightforward inspection will disclose any damage or bending.

How to readjust steering top top zero turn mower : Bonus tips

If you still experiencing a it was crooked straight, walk ahead andtry these extra ideas.

Tighten the linkage (stretching indigenous thesteering controller) where it connects come the mower’s pump motor/transmission,if loose-it fails to rotate fully affecting motion. Look for the managing boltthere.Examine (and change) the steering dampeners-theycause jerky motions when worn out. Finally, having identical tires (same do aswell together tread pattern) helps.

Wrapping it up

There walk our general guide on just how to change steering onzero revolve mower.

Naturally, particular models vary in design definition that theinstructions might be a little different.

But you shouldn’t fret- your owner’s manual is most likely tohave the relevant measures for your model.

Having said that, it’s finest to present your zero rotate to adealer for expert inspection and also repair if nothing works.

See more: (A+B)^3 Formula S - What Is The Formula Of (A

In fact, part manufacturers discourage consumers from adjusting reverse travel so contact your dealer if your zero turn tracks excessively appropriate or left in reverse.