A great drywall job starts v solid backing and also properly pushed fasteners. Learn just how pros make their finished drywall watch smooth and straight.

You are watching: How many screws per sheet of drywall


*

Photo 1: readjust screw pistol depth

Twist the nosepiece on the screw total to readjust the screw depth. Exercise driving screws top top a scrap the drywall donate by hardwood until you get the setup just right.


*

Photo 2: proper screw depth

The screw on the height is too shallow. Yes sir no room for share compound. The middle screw is just right. Yes a recess because that joint compound and the file face that the drywall is intact. The screw top top the bottom is as well deep. The paper face is take it through; the screw won’t hold.


How to placed Screws in Drywall

Don’t it is in tempted to use your cordless screwdriver or continuous drill to drive drywall screws. Neither will give you the an exact depth control you require for trouble-free fastening. Usage a screw pistol instead. They’re reasonably priced and easily accessible at home centers and also tool retailers.

Photo 1 shows how to change the screw total to collection screws in ~ the correct depth. Practice driving screws on a scrap of drywall or in a closet to get the hang of it prior to tackling her room. Start by placing a screw ~ above the magnetic driver tip. Then line up the screw v the center of the framing and squeeze the create to bring the driver as much as speed. ~ the motor is running full speed, push straight in and also don’t relax the press until the clutch starts come ratchet. You’ll recognize by the clattering sound that makes.

Make sure the drywall is tight


*

Photo 1: push drywall against studs

Press against the drywall while you drive in screws. Don’t release the press until you’ve driven two or 3 screws into the framing to distribution the load.


*

Close up

Screws will pop with the drywall if over there is a gap in between the stud and also the drywall. Pushing the drywall tight and also fastening several screws in the area will settle the problem.


Crooked studs or puffed-out insulation have the right to prevent the drywall native lying tightly versus the studs. If the space is too large, the screwhead will pop through rather than pulling the drywall tight.

Tack v nails, however fasten through screws


*

Ring-shank nails

Fasten the drywall in ar with a few ring-shank nails roughly the edges.


*

Drywall screw sizes

Finish fastening the drywall with drywall screws, which withstand popping and also hold much better than nails.


How plenty of Screws every Sheet the Drywall?

Buy 1-1/4-in. Coarse-thread drywall screws to affix 3/8-in., 1/2-in. And 5/8-in. Drywall to timber framing. Usage fine-thread screws to connect drywall to stole studs. To answer the question “how many screws per sheet of drywall?” it all relies how huge the piece of drywall is. But the most important component is to location screws 12 in. Apart wherein the end or edge of sheets butt at frame members, and along each framing member in the facility of the sheet. Nothing use much longer screws unless you’re screwing with soft material like foam insulation right into the basic framing. The screws need to only penetrate the timber 5/8 come 3/4 in. Any type of deeper and they’ll be susceptible to popping later.

For a speedier job, take a pointer from the pros and also tack the perimeter the the sheets with number of ring-shank drywall pond to host it. Then go back to drive the screws. This saves you the problem of delivering the screw gun around while you’re supporting the hefty drywall.

Provide hard backing ~ above edges prior to hanging the sheet


*

Photo 1: add backing in ~ corners

Screw 2×4 backing at the intersection that walls and also ceiling if the missing. Drill clearance holes at one angle with the height plate. Then journey 3-in. Drywall screws right into the 2×4 while you organize it down through your other hand.


*

Photo 2: add cleats

Nail or screw cleats alongside existing framing fairly than recutting the sheet. Be mindful to align the face of the cleat flush through the confront of the present framing before you pond or screw that in.


Inspect inside corners where wall surfaces intersect and also along the height of walls where they fulfill the ceiling. The score is to carry out at least 3/4 in. The exposed framing to drive screws into. If you can’t swing a hammer in tight spots, screw in blocking through 3-in. Screws. Save a couple of lumber scraps comfortable so girlfriend can include backing ~ above the fly if essential (Photo 2).

Mark the framing


*

Photo 1: note studs and joists

Avoid let go screws by marking all framing members prior to you begin hanging drywall. Note the ceiling frame on the top plate that the walls. Stop climbing a ladder through taping a pencil come the finish of a stick and using this to mark the framing. Then after the ceiling drywall is hung, note the centers that the wall surface studs ~ above the ceiling drywall.


*

Photo 2: show stud locations

Mark the facility of wall framing members top top the floor through a pencil or marker. Once you secure the top sheets of drywall, make certain to center a fastener on every framing member before hanging the lower sheet. Climate align a straightedge through the fastener and the clues on the floor and also draw a pencil line to mark the center of the framing.


It’s frustrating to need to guess wherein framing members room after they’re spanned with drywall. Avoid this problem by noting all the frame members prior to you begin hanging the drywall. Mark the center of every ceiling framing member on the optimal plate the the walls (Photo 1). After ~ you cave the ceiling drywall, note the wall surface stud centers ~ above the ceiling drywall and also on the floor (Photo 2). Usage a pencil when marking on drywall. Octopus from markers and also pens will certainly bleed with the paint.

Remove the screws that missed the framing


*

The problem

Pull the end screws that don’t catch the framing; they’ll reason problems later on when taping.


*

Photo 1: The solution

Remove screws that miss framing. Collection the screw total to reverse (there’s normally a little lever close to the switch). With the screw gun to run in reverse, use sideways pressure to the guideline of the screw gun if you pull it back and away from the wall to retract the screw. Also if the screw doesn’t come out, it have to be loosened enough to pull out by hand.


*

Photo 2: Clean up screw tears

Recess the fuzzy feet left indigenous screws that have actually been removed. Press the back of your utility knife versus the screw hole and twist while applying pressure to do a divot. Fill the recess later with joint compound.


Even with mindful preparation, you’ll occasionally miss out on a stud, drive a screw too deep or have trouble steering a screw deep enough. The screws nothing usually earlier out easily. Photo 1 reflects one an approach of removed screws with your screw gun. If this no work, on slide a putty knife blade under the head and press it versus the threads when you earlier out the screw through your screw gun, cordless drill or Phillips screwdriver. If you overdrive a screw and break with the paper, include another screw a few inches away and then remove the overdriven screw. Find underdriven screws through sliding your taping knife end each line of screws and also listening for clicks that indicate protruding screws. Usage a driver to twist them in a few turns, or eliminate them and also drive a brand-new screw alongside through the screw gun.

Required tools for this Project

Have the essential tools because that this DIY job lined up before you start—you’ll save time and frustration.

See more: How Much Is A Sprig Of Dill ? How Many Teaspoons Are In A Sprig

4-in-1 screwdriverChalk lineCordless drillDrywall sawDust maskHammerLevelScrew gunShop vacuumT-squareTaping knifeUtility knife

Required products for this Project

Avoid last-minute to buy trips by having all your materials ready front of time. Here’s a list.