The OBDII trouble code of P0335 is well-known as a “hard” code, definition severely detrimental come the operation of her Accord engine. Much more specifically the DTC P0335 represents a absence of signal indigenous the crankshaft place sensor. The crankshaft position sensor in her Honda Accord informs your ECU of the crankshaft speed and current location.

You are watching: 2000 honda accord crankshaft position sensor location

Without this data, the engine will either not run or run really poorly. Usual symptoms are an obstacle starting or the engine might shut turn off randomly, developing a an extremely dangerous situation for not just the driver yet the passengers together well.

Possible causes of OBDII inspect engine light P0335Bad or weak batteryBad StarterBad crankshaft position sensorDamaged sensor harness

Today I’ll be showing you just how to service and also replace your crankshaft place sensor in a 2000 Honda Accord with a F23A1 VTEC SOHC engine.

The part number because that this part is 37840-P0A-A01 because that the crankshaft place sensor in her Honda Accord. The can also be found under the part number of 37840-PAA-A01.


*

This How To adjust a Honda Accord Crankshaft place Sensor DIY guide assumes you have currently removed your driver next engine mount and also supported her engine through a jack. Please inspect our just how To readjust a Honda Accord timing Belt overview for much more details.

Before you start our DIY overview on how To change a Honda Accord Crankshaft position Sensor, you should disconnect the an unfavorable terminal on your battery. As stated previously, this overview assumes you have the right to raise and lower your F23 already, which is causing obligation when changing your time belt.

*

Unplug your four pin connector the runs to your crankshaft position sensor in her Honda Accord. Here’s what her pigtail watch like placed to your F23A1. It’s secured through a 10mm bolt the runs v the earlier of her VTEC SOHC engine.

*

This exploit to your crankshaft place sensor runs with your reduced timing plate, which need to be removed to change a Honda Accord Crankshaft place Sensor. In bespeak to perform this, friend must reduced your engine if still linked to her chassis, and also remove the crankshaft wheel or harmonic balancer.

This may be an overwhelming if you are working top top the ground v hand tools and don’t have a wait compressor with the appropriate air tools. Usage a Honda crankshaft wrench, Moroso part number 61805 to correctly loosen your crankshaft bolt there is no air tools.

*

With the bolt removed, girlfriend should have the ability to wiggle off her crankshaft wheel and set it safely come the side. Make sure eliminate your woodruff crucial and keep that as safe as your pulley.

*

Now you can remove every the 10mm bolts that organize your reduced timing covering in place. Remove these one-of-a-kind bolts and then do your means to the valve cover, you will require to ago off the valve covering bolts the run with to the cylinder head.

Loosen every the valve covering bolts, yet do not remove and also gently loosen her valve cover. Background the valve covering to allow enough room for your upper SOHC VTEC time cover come come off your engine. There space 2 10mm bolts that run v the top cover to the cylinder head, remove these to loosen your upper timing cover.

*

Now slide off your reduced timing cover and also pull down to release from your side motor mount. You must now see your time belt assembly and your F23A1 balance shafts and also belts. The crankshaft place sensor in her Honda Accord is situated behind the crank create plate.

*

You have the right to take one of two paths to removing her crankshaft position sensor and also replacing it. You have the right to loosen your timing belt tensioner bolt, the longated bolt situated in the middle of your tensioner arm. This should allow enough slack regarding gently earlier off your reduced crank sheave plate and also undo the 10mm bolt that holds the crankshaft place sensor in place.

*

If this is no an choice for you, examine out our just how To readjust a Honda Accord time Belt overview on exactly how to correctly time and also remove her F23A1 belts to company your crankshaft position sensor.

There are number of timing point out for her balance pillar that us recommend girlfriend line approximately TDC prior to removing her balance shaft belts.

See more: Can You Use Adult Aed Pads On A Child, Where To Place Aed Pads Child

*

Before removing your balance shaft belts to reach your crankshaft place sensor, friend will require to dual check time marks to ensure your F23a1 is at TDC. Again for much more details check our just how To DIY guide on transforming the Honda Accord timing belt.

*

Once you have actually replaced her Honda Accord crankshaft position sensor, you can use a scan device to properly clear your OBDII check engine code of P0335. Hope we’ve aided you learn exactly how To change a Honda Accord Crankshaft place Sensor, if you have any kind of questions please leave us a comment below!